Qingdao Wanhui Weiye teaches you how to use the double row drill correctly and precautions

2021-05-23

Correct use and precautions for double row drill


First, the drill switch description and use

1. Power on and off: The red button on the double row is the power on switch, rotate to the right and lift up to power on, press down to turn off.

2. Horizontal control: The first one of the red buttons is the horizontal control switch. The horizontal control is turned to the right and the reverse is closed.

3. Vertical control: The second button is the vertical control switch. The horizontal control is turned to the right and the reverse is closed.

4. School knife control: The red button is down to the third knife control switch. The horizontal control is turned to the right and the reverse is closed.

Second, the drill description and use

The red drill bit is reversed, the black drill bit is forward rotation, the horizontal drill bit should be installed first when loading the drill bit, and then the vertical drill bit should be installed correspondingly. When pulling the drill bit, the vertical drill bit should be pulled first, and then the horizontal drill bit should be pulled. When loading the drill bit, be sure to see the drill bit reverse.

Third, precautions before punching

1. Carefully analyze the order, clearly indicate that the punching should be noted, and mark it on the board, and communicate with the three rows and manually.

2. Carefully check the substrate to ensure the substrate is correct.

3. Carefully measure each plate carefully and pay attention to the damage of the plate when punching. If there is damage, obvious explosion, and direct replacement of the substrate.

4, carefully proofread the benchmark, to ensure that the cabinet is installed without obvious front mouth protruding indentation.

5. Cooperate with the three rows to record the problems that occur in the punching. After the plates are replenished, punch them in time and finish sending the packaging department.

6. If there is any objection, the double row must obey three rows.

Fourth, drilling operation instructions

Pulling: The normal pull width is 66mm. When the width is 66mm-90mm, two drill bits are installed horizontally when punching, and one bit is placed in the vertical direction. The drill bit in the vertical direction should correspond to the drill bit in the horizontal direction. Backing the mountain, the distance from the back of the mountain to the edge of the first hole is 14.20mm - 14.39mm. Three drill bits are mounted in the horizontal direction with a width of 100 mm and 112 mm, and one drill bit is placed in the vertical direction, and the drill bit in the vertical direction corresponds to the drill bit in the horizontal direction. 2. Top and bottom plate: When the top plate is topped (except for the width of 150mm or less), four drill bits are installed in the horizontal direction, and two drill bits are installed in the vertical direction. The drill bit in the vertical direction corresponds to the drill bit in the horizontal direction. The width of the top and bottom plates is different for the installation of the drill bits in different horizontal directions. The following are the mounting methods for the top and bottom horizontal drills of different widths:

100mm or less: 2 100mm - 150mm: 3 150mm side by side - 190mm side by side 4 190mm - 220mm: empty 1 230mm - 250mm empty 2 260mm - 280mm empty 3 290mm - 310mm empty 4 320mm - 350mm empty 5 360mm - 380mm empty 6 390mm - 410mm empty 7 420mm - 440mm empty 8 450mm - 470mm empty 9 480mm - 500mm empty 10 510mm - 530mm empty 11 540mm or more 12 empty

3, disinfection cabinet A bottom plate: from the rear mouth to the outside of the drill bit to adjust one, the middle of the empty. The bottom plate of the cabinet bottom R717 handle is adjusted from the front side of the front mouth to the inside of the horizontal direction.

Five, operating precautions

1. Lubricating oil should be added to the machine tool on time, according to quantity and according to requirements.

2. The operator must be familiar with the structural performance and working principle of the machine tool to achieve safe production.

3. The operator should be dressed neatly and must not wear long clothes to avoid accidents.

4. The operator must not approach or touch any rotating part of the machine with bare hands. Do not wear gloves to avoid the impact of the edge of the blade.

5. It is strictly forbidden to operate the machine tool in sick condition and after drinking.

6. When the machine is running, the operator must concentrate and stick to the post.

7. Keep the work site clean and well lit. Do not place tools and other objects on the machine.

8. The machine should be turned off when the operator leaves the machine.

9. The machine should be cleaned after the operation is completed.
Release time: 2014-01-13


First, the drill switch description and use

1. Power on and off: The red button on the double row is the power on switch, rotate to the right and lift up to power on, press down to turn off.

2. Horizontal control: The first one of the red buttons is the horizontal control switch. The horizontal control is turned to the right and the reverse is closed.

3. Vertical control: The second button is the vertical control switch. The horizontal control is turned to the right and the reverse is closed.

4. School knife control: The red button is down to the third knife control switch. The horizontal control is turned to the right and the reverse is closed.

Second, the drill description and use

The red drill bit is reversed, the black drill bit is forward rotation, the horizontal drill bit should be installed first when loading the drill bit, and then the vertical drill bit should be installed correspondingly. When pulling the drill bit, the vertical drill bit should be pulled first, and then the horizontal drill bit should be pulled. When loading the drill bit, be sure to see the drill bit reverse.

Third, precautions before punching

1. Carefully analyze the order, clearly indicate that the punching should be noted, and mark it on the board, and communicate with the three rows and manually.

2. Carefully check the substrate to ensure the substrate is correct.

3. Carefully measure each plate carefully and pay attention to the damage of the plate when punching. If there is damage, obvious explosion, and direct replacement of the substrate.

4, carefully proofread the benchmark, to ensure that the cabinet is installed without obvious front mouth protruding indentation.

5. Cooperate with the three rows to record the problems that occur in the punching. After the plates are replenished, punch them in time and finish sending the packaging department.

6. If there is any objection, the double row must obey three rows.

Fourth, drilling operation instructions

Pulling: The normal pull width is 66mm. When the width is 66mm-90mm, two drill bits are installed horizontally when punching, and one bit is placed in the vertical direction. The drill bit in the vertical direction should correspond to the drill bit in the horizontal direction. Backing the mountain, the distance from the back of the mountain to the edge of the first hole is 14.20mm - 14.39mm. Three drill bits are mounted in the horizontal direction with a width of 100 mm and 112 mm, and one drill bit is placed in the vertical direction, and the drill bit in the vertical direction corresponds to the drill bit in the horizontal direction. 2. Top and bottom plate: When the top plate is topped (except for the width of 150mm or less), four drill bits are installed in the horizontal direction, and two drill bits are installed in the vertical direction. The drill bit in the vertical direction corresponds to the drill bit in the horizontal direction. The width of the top and bottom plates is different for the installation of the drill bits in different horizontal directions. The following are the mounting methods for the top and bottom horizontal drills of different widths:

100mm or less: 2 100mm - 150mm: 3 150mm side by side - 190mm side by side 4 190mm - 220mm: empty 1 230mm - 250mm empty 2 260mm - 280mm empty 3 290mm - 310mm empty 4 320mm - 350mm empty 5 360mm - 380mm empty 6 390mm - 410mm empty 7 420mm - 440mm empty 8 450mm - 470mm empty 9 480mm - 500mm empty 10 510mm - 530mm empty 11 540mm or more 12 empty

3, disinfection cabinet A bottom plate: from the rear mouth to the outside of the drill bit to adjust one, the middle of the empty. The bottom plate of the cabinet bottom R717 handle is adjusted from the front side of the front mouth to the inside of the horizontal direction.

Five, operating precautions

1. Lubricating oil should be added to the machine tool on time, according to quantity and according to requirements.

2. The operator must be familiar with the structural performance and working principle of the machine tool to achieve safe production.

3. The operator should be dressed neatly and must not wear long clothes to avoid accidents.

4. The operator must not approach or touch any rotating part of the machine with bare hands. Do not wear gloves to avoid the impact of the edge of the blade.

5. It is strictly forbidden to operate the machine tool in sick condition and after drinking.

6. When the machine is running, the operator must concentrate and stick to the post.

7. Keep the work site clean and well lit. Do not place tools and other objects on the machine.

8. The machine should be turned off when the operator leaves the machine.

9. The machine should be cleaned after the operation is completed.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn

Vertical Drilling Machine, Vertical Drill Press, Bosch Drilling Machine, Core Drilling Machine
Head Science & Technology Corporation http://www.weissmachinerys.com